The trailer wheel part # LHSL311 was designed to be used with a standard center cap like the part # 425EZ. I am not totally sure what type of wheel you are looking for but if you could get me the size, bolt pattern, and a picture of it I can see what the closest match would be. view full answer...
For the dimensions of the Replacement Lamp Switch for Ventline RV Range Hood # BL0108-01, I confirmed that the overall dimensions of the switch are .85 inches high x .594 inches wide. As far as the cutout for the hole, that dimension is .756 inches high x .508 inches wide. I went ahead and attached diagrams of these dimensions. view full answer...
The opening in the Gustafson Glass for RV Pendant and Sidewall Lights # 277-000430 that connects to the base has a 1" diameter. I have attached a photo to demonstrate. view full answer...
The Dexter leaf springs part # DX74XR are for an 8,000 lb rated trailer axle. Individually that would mean they would be rated at 4,000 lbs. view full answer...
I have attached for you below the complete dimensions of the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 part # LC349975 to the degree that Lippert was willing to share. If you require further dimensions, I'd need to know exactly what that is to see if we are able to obtain these for you. That said, manufacturers typically don't release full CAD for products to prevent design theft so we are also limited in what we can provide. view full answer...
I reached out to Roadmaster about the Comfort Ride Leaf Spring Suspension Kit w/ Shocks # RM-2460-2580 you are looking to install. While they are unable to give exact numbers for the length of travel on the leaf springs the shocks do have 5-1/2" of maximum travel. You may notice an initial change in ride height due to the new and heavier leaf springs but the system is not designed to increase your overall ride height on your 2018 Grand Design Momentum 351M 5th wheel camper. view full answer...
If your 2021 Grand Design Solitude 375RES is loaded when you're taking that measurement then yes, that would be why you're seeing a difference in the length from what you're measuring and what we have listed for the 7-Leaf Double-Eye Spring for 8,000-lb Trailer Axles - 24-7/8" Long # DX74XR.
As weight is placed on the springs they naturally flex which is why you're seeing what you're seeing.
Attached is a review video for you to check out! view full answer...
The weight of 1 of the Stromberg Carlson Base Pad Extreme for RVs and Trailers # SC33VR is approximately 4.5 lbs.
If you were wanting to know the weight capacity, it is 6,000 lbs. individually or 3,500 lbs. when 2 are stacked together. view full answer...
I would be happy to help you. There are a few ladder racks that use the stake pockets but for your application there's nothing with that style mounting method.
I recommend the Yakima BedRock HD Truck Bed Rack item # Y01160-59. These crossbars attach similar to a bed liner or camper shell. They use clamps to secure them to your Silverado's bedsides. The included locks will help to prevent theft.
The Kuat Piston item # KU32VR is a great option and would have more than enough capacity... view full answer...
Per the manufacturer The length of the threaded pipes in the back of The Replacement Quick Disconnect Shower Valve for Empire Faucets Exterior RV Showers - Black # EM84FR is 1.64 inches, and from center of pipe to center of pipe is 4 inches.
I attached a picture below. view full answer...
Trailer tires need to be ran at their max psi rating to ensure you get the full capacity and speed rating. Otherwise the tire will most likely fail early due to heat build up. So for the Westlake ST225/75R15 Radial Trailer Tire w/ 15" Silver Mod Wheel # LHAW124 you'd want to fill up to 80 psi when cold and you'd be good. No need to worry about psi changes due to temp changes either. view full answer...
The top of the line cover we have for your 2023 Grand Design Momentum 320G is the Adco SFS AquaShed RV Cover for 5th Wheel Toy Haulers item # 290-52256. This cover will stand up well against wind, rain, and snowy climates.
The Adco Cover item # 290-52256 has zippered panels on the passenger's side and rear to offer access to to your trailer while in storage. The reinforced, elastic corners ensure a snug fit, reduce wear, and help against tears and snags. The cinch ropes at the front and... view full answer...
The center hole diameter on the Gustafson RV Ceiling Light Shade - 11" Diameter - Frosted Acrylic # 277-000495 measures 1". The overall dimensions are 11" diameter x 3-1/2" tall. view full answer...
There are two options to add a rear hitch to your Grand Design Solitude. I have listed them below along with any installation videos we may have:
By far the easiest option is going to be the Curt RV Bumper 2" Trailer Hitch Receiver item # E-100. This hitch simple bolts onto your rear bumper so long as it is a 4" square channel bumper. I recommended checking to see if your bumper is reinforced and has a stated weight capacity before making this purchase. You will also want to check the... view full answer...
The Aluminum Liger Trailer Wheel part # LH35FR will have a 0.453" valve stem hole. Generally speaking, wheels under 16" will be 0.453" and wheels over 16" will be 0.625". view full answer...
We do!
I recommend going with the Aluminum Viking Series Valhalla Trailer Wheel # TA75FR which is compatible with up to 100 psi but you'll need to swap out the rubber valve stem (only rated for up to 80 psi) to the Americana Metal, Bolt-In Valve Stem # AM20906.
The metal valve stem can handle up to 200 psi so you can be confident in the performance and safety of this wheel and valve stem setup. view full answer...
Sounds like you might have auto running lights on your truck which is then activating the running lights on your trailer and then turning on the camera of the # FOS43TASF that you have. Have you tried turning on the running lights or headlights of the truck when it's in reverse to see if that keeps the camera activated. view full answer...
The standard diameter for trailer leaf spring bolts is 9/16 inch which is why the part # E4139 and all similar options have this hole size. We don't have anything with a smaller diameter but my guess is what you have is actually 9/16 inch. view full answer...
I checked with Trailair/Lippert and they state that the Trailair pin box part # LC158778 weighs 185 and can be done as a DIY project but you'd need either one really strong friend or two reasonably strong friends to hold the pin box while you bolt into in place. Or if you had access to someone who is forklift certified who could lift it into place while you bolt it in. That's how we do it here.
Pin box bolt torque is based on the size of the bolts.
1/2 inch Bolts GR5 90 ft-lbs
5/8 inch... view full answer...